How to set up a modem on iPhone SE. How to activate tethering mode on iPhone in the easiest way

You can make it out of an iPhone wi-fi router and distribute the Internet to other devices. Very useful if you are far from home if your laptop does not have a 3G modem. In this article we will talk about how to enable iPhone tethering mode, as well as some problems that you may encounter in the process.

After that mobile device turn into a mobile hotspot and begin to “distribute” the Internet. You can connect to it via Wi-Fi using the password that is displayed in the mode settings.

Be careful: On mode wi-fi modem not shown anywhere. But the battery on your phone drains faster.

When another device connects to you, you will see this message in the status panel.

Setting up another device connection

To connect to the created Wi-Fi network from another device, go to the network settings on this device. Select a title wi-fi points, which you specified in the settings. And enter the access password.

This is what connecting to an iPhone on a MacBook looks like. On other devices, the connection icons will be identical.

It is worth highlighting several main features of using modem mode:

• Don't expect high speeds, since the Internet connection is via a mobile network.
• When modem mode is activated, the autonomy of the mobile device is slightly reduced.
• Some operators mobile communications may impose some restrictions on the number of simultaneous connections to one device.

What to do if modem mode on iPhone cannot be activated

In some cases, to activate modem mode, users will have to carry out a series of additional settings. It depends on the cellular operators. In particular, here is an article on how to enable yota modem mode. General principle such:

Mobile operator data:

Russia

Beeline / Beeline

• APN: internet.beeline.ru
• Username: beelin
• Password: beeline

MTS / MTS Russia

• APN: internet.mts.ru
• Username: mts
• Password: mts

MegaFon / MegaFon

• APN: internet
• Username: gdata
• Password: gdata

Tele2 / Tele2 Russia

• APN: internet.tele2.ru
• Password: leave blank

• APN:yota
• Username: yota
• Password: yota

Ukraine

Kyivstar

• Username: leave blank
• Password: leave blank

Lifecell Ukraine

• APN: internet
• Username: leave blank
• Password: leave blank

MTS Ukraine

You can clarify your APN data by calling 111 for MTS Ukraine users.

iPhone represents universal device, which has a number of advantages, one of which is its ability to act as a modem. Using this phone versions 4s, 5s, 6 and so on, any subscriber can distribute traffic within the network’s range. This can be done using a special mode, which you just need to activate and make small settings to provide the Internet to any device, from smartphones to PCs. But not every owner of such a mobile device knows how to correctly enable modem mode on the iPhone 6, but this can be done very easily.

No modem mode

Sometimes it happens that after installing scheduled updates on iPhone 6, 5s, 4s, as well as its other versions, various network settings stop working or are completely deleted. The modem mode stops functioning, or the system constantly freezes on the window of the running processor. This situation repeats itself periodically and no user is protected from it.

Removing modem mode occurs not only in iPhones 5s and 4s, but also in 6, since the ninth version of iOS also failed to cope with the problem in question. Updating the phone leads to the fact that the corresponding item from the menu simply disappears, or when turned on, the mobile device completely freezes in a neglected state.

In fact, the modem distribution service does not disappear and is not deleted. In fact, it looks like Apple simply turned off this function by default, explaining their action by the fact that subscribers practically do not use this mode. But these are not all the reasons. The function in question was disabled in order not to bear responsibility for its operation, taking into account the peculiarities of Internet settings and operators of various countries around the planet.

In fact, a large number of users are accustomed to using iPhone 4s, 5s, 6 and other versions as an access point, the removal of which makes them practically helpless. For example, when traveling, it is much more convenient to work on a PC, accessing the Internet from your phone, without using other complex and inconvenient routers. That is why it is necessary to find an answer to the question of how you can restore the ability to distribute Internet traffic using an iPhone.

Activating modem mode

In the case when on iPhone 6, 5s, 4s, or other versions of this smartphone, namely in iOS 9, the connection in modem mode stops functioning, the subscriber must first turn it on, and then manually write the details of his operator.

To successfully carry out these actions, you must do everything clearly and correctly, observing the following sequence:

1. You need to find the cellular communications department in the settings.
2. Then find the line called “Modem Mode” and change its status to enabled.
3. After activating the modem mode, the subscriber should enter the settings of the operator used by filling out the appropriate fields, as well as the cellular data tabs.

The information that needs to be entered changes accordingly with the operator, so you need to be careful. Data to enter:

After filling out the settings in iPhone 5s, 4s and other versions mobile operator, the “Modem Mode” service becomes available for use. You can find out the necessary modem settings of other mobile operators directly from them by calling their hotline number.

Also, you should pay attention Special attention the fact that when running mode modem given mobile device V automatic mode will distribute Internet traffic to the PC, with any connection via a USB cable. This will happen even if this is the next synchronization intended for organizing backup copies using iTunes. Therefore, it is better to disable the option in question when it is not in use, because the fee for its use continues to be charged, and by disabling it, you can save your own cash.

Hi all. I decided to collect all the data about the modem mode in one place. The funny thing is that for 4 years on our website we have never written about this topic... I’m correcting myself.

Modem mode allows you to connect computers and devices to the Internet through the device's cellular data network. Modem mode is available on the following devices: iPhone 4 and higher (with certain conditions 3G and 3GS), iPad 3 Wi-Fi Cellular (or later), iPad Mini Wi-Fi + Cellular (or later).

Enabling modem mode

By default, modem mode is disabled. To enable modem mode, you need to:

1. Settings-> cellular-> Cellular data - turn on the switch.

Settings->Cellular->Enable LTE - if such a switch is available.

2. Settings->Cellular->Modem mode->Modem mode. You need to turn on the switch. For the first time, the device will prompt you to turn on Bluetooth or use only USB/Wi-Fi. That is, the Internet can be distributed not only via Wi-Fi, but also via USB and Bluetooth.

If the default password is a simple one, change it to a more complex one.

Connecting other devices

Connecting another device to the Internet using Wi-Fi modem mode is now easier than ever. We find the one we need among the Wi-Fi networks - it will have a chain icon. Enter the password. Done - the second device now uses the Internet of the first.

On a device that shares the Internet, the status bar will turn blue. And the line will be written in it: “Modem mode - connections: 1.” If you have 1 device connected via modem mode, and the number is higher, it means someone else has connected to your Internet. There is no need to panic - most likely, some device nearby that was connected earlier has automatically joined the network... If you cannot find such a device (and we had a similar experience :)), then the easiest way is to change the password for the Wi-Fi network in dispenser.

Important point! A Wi-Fi connection cannot be used to access the Internet when other devices are using the Wi-Fi network in tethering mode. You can only share your cellular data connection, not your Wi-Fi network.

Setting up modem mode

After updating iOS 8.0.2, modem mode disappeared on some iPads and iPhones. I personally saw this problem on the iPad Mini 1. After that I decided to write these instructions. This is a bug! To fix it, you just need to enter the APN settings in the appropriate places.

Settings->Cellular->Cellular Data Network. In chapter Modem mode enter the settings of your operator.

Belarus

Users of OS version 9 often report the following error: the modem mode has disappeared. On iPad, tethering mode most often fails when updating more than earlier versions devices up to iOS 9.

The problem manifests itself in different ways, depending on the communication company whose SIM card is in the gadget. For some users, the option disappears from the corresponding menu without a trace, for others it does not function correctly. Sometimes it is not possible to enable modem mode at all.

This material will discuss the causes of this problem and how to fix them.

Usually the malfunction manifests itself in the same way on absolutely any gadget (second iPad and others), and with any telecom operator (Yota and the like). And all because it is in no way related to hardware problems or specifics specific model device In 95% of cases, the malfunction manifests itself after updating the device to a more recent version. Through experience, users found out that the cause of the failure was a configuration reset of the cellular company.

As a rule, it is set automatically. All the necessary data is contained in the SIM card's memory. However, when updating, everything that is possible is reset, and the modem mode stops working.

Error correction methods

The algorithm for solving the problem, based on its essence, will be identical for all iOS gadgets (iPad 2, iPad mini, Pro and others). The user is required to configure APN for modem mode.

What does this mean? This is the name and at the same time the address of the access point through which the user connects to the network. Of course, you will need a password and username. The telecom company will read these characters and assign the correct IP address to the network. Next, a connection will occur to the corresponding security element. It will also determine whether the connection needs to be configured via private networks. In the situation we are considering, when using modem mode, the gadget will transmit access to its communications company to other devices over the network.

The user is required to perform the following actions:

• Open settings, go to the cellular connection point. Then you need to go to the cellular data network.
• On the page that pops up you will see the modem mode item, and below it there are 3 fields. If they are empty, you should fill them. For the correct operation of the mode we need, proper APN configuration is required.
• Filling out the fields in accordance with the data of a specific operator.

This information can be found in the contract with the telecom company. Or contact the company office directly. Usually, after applying all the methods, the problem is solved, and the device can again be used as a modem for any operators - Yota and others.

Other causes of the problem

Problems may also lie in the following points:

• Communication company restrictions. If the problem was not solved by the method described above, it means that the company providing the services has imposed some restrictions. A number of operators block distribution of the network to other devices on their tariffs unlimited plan. The user should read the contract more carefully, and if there are restrictions, he just needs to change the tariff.
• Error during update operation. If you did not find any restrictions in the document, the problem may arise due to an error that occurred during the process of updating the device to a higher version. new version. In this case, you will need to use flashing the OS, that is, installing the same iOS versions on a new one.

Please note that during the flashing process, the settings return to the original ones. Therefore, it is recommended to make a backup in advance using iTunes and save it on your PC for later restoration:

• Connect the device to the PC.
• In the program window, click on the gadget icon at the top left.
• Select a location to save the copy - on a PC or in the cloud. Confirm immediate creation of a copy.
• Backup contains all the information stored on the device. Therefore, in the future it will be possible to return any information back.
• Proceed with the firmware operation. Determine the tablet model. It is important that the OS version matches the specific tablet model.
• Upload the firmware file as .ipsw. This should be done only from high-quality resources. Otherwise, you can catch a virus on both your PC and iOS device.
• Disable the device search function. Otherwise, it will interfere with the firmware and will not allow it to be done.
• Turn off the device. Connect it to a PC or laptop by holding down the “Home” button. This is how you enter the device into Recovery mode Mode.
• Click on the restore button on the iPad, thereby turning on the file manager.
• Use the iTunes utility. It instantly recognizes the connected tablet. Next, you need to click on the device symbol (located at the top, on the left side), and then on the recovery element.
• Open the downloaded firmware file in the manager. Wait for the operation to complete. Re-do the APN settings of the modem (for Yota and the like).

The method used above should definitely help. And if this does not happen, turn to more radical methods.

Device malfunction

How to enable the mode in question if it begins to disappear?

If the firmware did not give anything, then the problem lies in the hardware of the device. The modem module is probably faulty, which is why modem mode on the iPad is not working. There's nothing you can do about it - you'll have to go to a repair shop. You won't be able to simply connect to the iPad's network if the problem hasn't been fixed.

Note that in the ninth version of the operating system there are problems with malfunction Modem mode is solved very simply. The user must use the username and password for the carrier's access point. But if this step does not help, be sure to contact a specialist. Experienced craftsmen identify the source of the problem and fix it. And the device can again be used as a modem (for Yota and other operators).

An iPhone can be used as a modem that distributes mobile Internet to other devices. Using Modem Mode, an iPhone can distribute the Internet to a computer, smartphone or tablet, which is sometimes very convenient. Distribution to a computer can occur via a USB cable or wireless Wi-Fi and Bluetooth. It is not possible to distribute the Internet to other phones via cable, only wirelessly.

Today's issue:

If you decide to use Modem Mode and connect to iPhone computer or other devices to transfer the Internet to them, then first you need:

• Have an iPhone 3G or higher (not)
• It is desirable that the speed be good

If the Internet is connected and your Safari browser accesses Internet pages, then proceed to setting up and enabling Modem Mode.

Modem mode is in iPhone settings, launch the Settings application and look. If there is a Modem Mode section in the main menu or in the settings of the Cellular section, it means that the modem mode was enabled when setting up the Internet on the iPhone.

How to set up tethering mode on iPhone

Why is there no Modem Mode in Settings or in the Cellular section? Because it needs to be configured, and it will appear, provided that your cellular operator supports this feature.

We will configure the modem mode using the example of the Tele2 operator. Let's launch standard application Settings – Cellular – turn on Cellular Data and go to Data Options

Select Cellular Data Network and scroll to the very bottom, where the Modem Mode settings are located and enter the APN – internet.tele2.ru (Modem Mode setting for Tele2, I tried writing just internet, it also works).

Each operator and each country has its own settings; you can find them on the website or by contacting the support service of your cellular operator. Sometimes discussions about your region's settings profile can be found using search engines Internet, enter in search engines “ Modem APN mode and the name of your operator and country».

After entering APN settings for Modem Mode, go to and exit the Cellular section several times (located in the main menu of the settings application), if Modem Mode does not appear, then .

How to distribute Internet from iPhone to computer

The first thing we will learn is how to connect the Internet to a computer via iPhone. USB cable using Modem Mode. Before we begin, make sure you have Cellular Data turned on on your phone (found in Settings - Cellular).

Connect the iPhone to the computer using a USB cable. It is advisable to use a native USB cable, as there may be problems with low-quality replicas. Go to Settings – Modem mode – turn on the Modem mode toggle switch and click – USB only.

That's it, the iPhone distributes its mobile Internet to the computer via USB. Fast and convenient. Open a browser on your computer and try to access any page on the Internet. Tested on Windows 7 and Mac OS X El Capitan. If for some reason the Internet does not appear on the computer, then (preferably) or a separate file AppleMobileDeviceSupport.msi (contains drivers for iPhone). Sometimes it helps to disable the firewall or antivirus on your computer, which can block traffic.

Distributing Internet from iPhone via Wi-Fi to other devices

In this case we use iPhone as wireless modem, distributing the Internet via Wi-Fi. The advantage of this method is that neither a USB cable nor iTunes is needed. The only requirement is the presence of a Wi-Fi module in the device that will receive the Internet from the iPhone (be it a tablet, phone or computer).

The process of enabling mobile hotspot on iPhone is simple. Go. As in the previous example, make sure that Cellular Data is turned on on your iPhone (2).

To enable the access point, select in Settings – Modem mode (3) – Enable Modem mode (4). In principle, at the 4th point the access point in the iPhone will be turned on, but if the phone is connected to the computer at this time, you will need to additionally click – Turn on Wi-Fi and Bluetooth (5).

Modem mode on iPhone - what is the password?

The iPhone is ready to distribute the Internet via Wi-Fi and Bluetooth, using Modem Mode, the phone has become an access point. All that remains is to connect devices that need the Internet, for this you also need to turn on Wi-Fi, find your iPhone in the list of devices and connect to it using a password, the password for the iPhone hotspot can be found here: Settings - Modem mode - Wi-Fi password. In the same section, you can change your iPhone hotspot password. Just don’t set a password like in our example in the picture, otherwise it can be easily guessed and used by strangers.

We connect a computer with Windows 7, 8 to an iPhone Wi-Fi access point

Having turned on the modem mode in the iPhone, and having figured out the access point password, we will distribute the Internet to the computer under Windows control over a Wi-Fi network. The network will be organized between the iPhone and the computer. Turn on Modem Mode on your iPhone and select – Turn on Wi-Fi and Bluetooth. On a computer with Windows 7 or 8, at the bottom, near the clock, click the Wi-Fi icon (1), select iPhone (2), click Connect (3), enter (4) and click OK (5). Mobile Internet I went from my iPhone via Wi-Fi to my PC, and now I can access the network from it.

If, after entering the password, the PC cannot connect to the iPhone, despite entering the correct password, then in Windows 7, by clicking on the Wi-Fi icon, select Network and Sharing Center - Manage wireless networks– and remove the iPhone from the list (right click – Remove network), then try to establish the connection again. In Windows 8, in this case, in the list of Wi-Fi networks, right-click on the iPhone - Forget this network.

We connect a computer with Mac OS to Wi-Fi via iPhone

iPhone modem mode is enabled. To connect a Mac OS computer to an iPhone wireless access point and use its Internet, you need to in Mac OS, in the upper right corner, click on the Wi-Fi icon (1) – Enable Wi-Fi (2) – Select the iPhone with the icon from the list modem mode (two rings) – lead – press Connect (5). We use the Internet.