Paracord is a lightweight and very durable nylon cord. It was previously used in the manufacture of parachutes, but today it is successfully used for other purposes. Paracord is used to make bracelets, keychains and belts. Sometimes they are purely decorative, and sometimes they are practical.

We invite you to get to know this material a little closer, and also master paracord weaving. In this article you will find diagrams, practical tips and other useful materials.

What is paracord?

Paracord is a cord made of several nylon fibers securely connected to each other. That is why the most durable types can withstand weights of more than 300 kg. However, finding such material is not easy. In the departments for creativity, its analogues are presented, which, of course, are also durable, but may not withstand the weight of a person.

If you want to make a bracelet or keychain out of paracord for practical purposes (to take with you on a hike, for example), look into the extreme equipment departments or hardware stores. Nylon cords are more reliable there. They may not be as bright, but they perform their main function with a bang.

Why is it better than twine?

Let's note 4 main advantages:

1. Paracord is lighter than standard twine. If you are planning to go on a hike or expedition, this point is important. The equipment of military personnel also meant that every gram was taken into account, so paracord has a clear advantage here.
2. It's stronger. Well, this is all clear.
3. The weather has no control over him. If the twine rots in dampness, the paracord will dry quickly. Even mold does not attack it, so paracord bracelets can be left on even while swimming.
4. It is easy to weave and unravel. Over time, a knot made of twine will become impossible to untie. Paracord is easy to untangle, but this does not make the knots any less secure.

Why do Boy Scouts need paracord?

Paracord is familiar to every Boy Scout. Participants in the movement are taught to weave “survival bracelets.” Young men wear them on their hands or as key rings on their backpacks. It is understood that in extreme conditions the bracelet will be unraveled back into a three-meter nylon cord. After use, Boy Scouts can re-weave the bracelet and place it on their arm again. This useful skill helps save space in your backpack and ensures the safety of the nylon thread.

Fun fact: in the movie Mad Max, the main character wears a paracord bracelet on his arm. After this, it became very popular among men as an everyday accessory.

Hikers and fishermen also borrowed this idea from scouts.

Paracord in creativity

Today, paracord bracelets have become popular jewelry for men and women. All thanks to the availability, practicality and beauty of nylon cords. Many interesting paracord weaving patterns have emerged that use a combination of different colors.

Whatever you decide to use your paracord bracelet or keychain for, it can be made into a truly beautiful modern accessory.

Weaving

For one bracelet we will need 2-3 meters of paracord. It is most convenient to weave using a clamp. You can secure the cord with a paper staple.

Weaving patterns for paracord accessories are borrowed from technology. Let's talk about the most popular of them.

The pattern that the Boy Scouts use is as follows.

The result is a simple, cute and very reliable bracelet, which, if desired, can easily be turned back into a paracord cord. If necessary, make it long - you will get a belt.

A simple type of weaving that can be completed with a fastening or a knot.

If you don’t quite understand how to weave a paracord bracelet, you can watch this visual video master class.

As you can see, weaving is really very simple. A little practice and everything will work out.

Another good way is to braid a thread of one color with a long cord of a different color. This is perhaps the simplest paracord bracelet design.

The central cord matches the length of the bracelet. The second is approximately 2-3 meters. Take a look at the photo to understand how to correctly braid the central part with the second cord.

The result is not only reliable and practical, but also a beautiful bracelet. With a successful combination of colors, it looks advantageous. It’s also not too bulky, so it’s also suitable for girls.

To make a 4-color paracord bracelet, you will have to fuse together several cords of different colors. To do this, simply heat and tightly connect the edges of the nylon rope. Just keep in mind that you shouldn’t use the entire cord while traveling – the fastening may not be reliable. This is more of a decorative move.

The weaving pattern in this case is as follows.

With a successful combination of colors, you get a beautiful and very original accessory.

There is another popular option for weaving paracord bracelets - a snake. This master class shows how to make an accessory correctly. In addition, in the video you will learn how to complete a paracord bracelet with a fastener.

If you want to make a paracord keychain, you don't need to complete it. Simply tie each loose end into a knot and leave it dangling freely. When making a complete bracelet without a clasp, the last row is simply woven into the first. You can also weave bracelets from paracord using floss patterns (check out our material on this topic). Choose the appropriate method and color of nylon cord. We hope that these reliable accessories will become your faithful assistants and complement your look!

Views: 6,395

Paracord bracelets are not only a simple accessory and part of clothing, they really look stylish and beautiful, but the beauty of such a bracelet is that you can take it with you on a hike or in the forest in nature and, if necessary, you can unravel it and get quite a long and strong rope. The length of such a rope in a bracelet can reach from 2 to 10 meters and depends on the type of weaving, of which there are several. In this article we will weave a paracord bracelet using the “snake” technique, it is the simplest, which will allow you to weave it quite quickly and it can accommodate it contains from 2.5 to 3 meters of paracord, depending on the thickness of the hand of the person for whom this bracelet is being made. This length of rope is enough for many cases and it can come to the rescue at any time.

What we need:

• 2.5 meters of paracord;
• Plastic fastex (latch);
• Scissors;
• Lighter.

The process of weaving a paracord bracelet:

Fold the rope in half.

We pass the middle of the paracord through the eye of one half of the fastener and throw a loop through it. This half of the fastex should be the inner part from you, since there are fasteners that have an inner part and an outer part, this can be seen from the hole for the strap, which is more bent to one side.

Do not tighten the created loop yet. We take the ends of the packacord and pull it together through the eye of the fastex exactly in the middle between the turns.

Then we thread these ends into a loop (the middle of the paracord) and pull these two ends through it to the very end and tighten this entire knot, while straightening this knot so that the turns lie evenly and correctly on both sides.

Now we put the second part of the fastener on the ends of the ropes, and leave it at some distance from the first part, while the inner part of this fastener was directed like the first - away from us. The ropes should be parallel to each other and not intertwined.

We get the basis for weaving a bracelet:

We put this base on the hand and at the same time adjust the length of the bracelet, now everything is moving well and you can tighten and loosen it without problems. The most suitable bracelet length is when you can freely put one finger under the strap.

Now you can directly begin weaving a paracord bracelet using the “snake” technique.

To do this, first we will align all the loops and parts of the rope, and then take the bracelet again, so that the inner part of the clasps looks away from us, and the outer part towards us. We first thread the left end of the paracord through the left rope of the bracelet base (above it), and then thread it under the bottom of the right rope.

Then we pass the right end of the paracord through the right rope of the bracelet base (above it), and then thread it under the left rope of the bracelet base from below.

Then we wrap the same end over the left warp rope and then run it under the right warp rope.

Now we take the other (left) end again and continue to weave according to the same pattern, alternating the ends. Straightening each time and tightening the loops.

Approaching the end of the weaving, you need to compact all the turns to the beginning of the weaving over the entire surface. This will free up space for a few more weaves.

At the end of the weaving, the ends should go inside the bracelet, where the excess should be cut off and the ends of the paracord should be burned with a lighter.

So we learned how to weave a bracelet from paracord; in total it took about 15 minutes at a slow pace.

Paracord weaving

Paracord weaving includes many techniques for creating multifunctional accessories. Merchandise stores for real men are replete with a variety of paracord bracelets, differing in style, thickness, final cable length, and additional elements. However, the most durable product can be considered a hand-made product, since its owner can be one hundred percent sure of its strength and reliability. Next, we will look at how to make a high-quality survivalist bracelet or lanyard with your own hands, as well as what tools are recommended to use for weaving paracord.

Paracord weaving

Paracord is a durable synthetic material (Figure 1), has a wide range of applications and high load-bearing capacity. Weaving from paracord became popular thanks to American paratroopers, who cut the cables from used parachutes for survival purposes. From such a cable it is easy to make a snare for catching small game and insurance for moving in the rocks, apply a splint and stop the bleeding, secure the sail cloth on a raft and yacht, or tent awning, insert into boots instead of laces, and even sew up a wound if unraveled into a thinner cord. Methods of operation vary solely from the situation and resourcefulness of the owner.

Figure 1. This is what paracord looks like

Since in critical conditions it is not always possible to remove the backpack to get a skein of lace, the most convenient method of wearing is an easily unfastened bracelet attached to the wrist. Having such a product on your body, you can quickly react and get out of even the most difficult situation without wasting time. A paracord bracelet is woven using simple patterns involving one or more cables. The patterns came to us from macrame and consist of knitting loops and weaving cord. The advantage of use is versatility and durability. Synthetic fibers do not rot, do not become covered with fungus or rust, are slightly dirty, burn relatively poorly, and moisture disappears from them almost instantly.

How to choose paracord

Before weaving a paracord bracelet, you need to choose the right cord. If you get to know paracord more closely, it is a type of nylon, considered one of the strongest synthetic materials.

The structure of the lace is divided into:

• Internal base (Figure 2). It is woven from several thin and strong cords (up to approximately 1 millimeter in diameter each), which can be quickly pulled out, unbraided and used for sewing, as a fishing line for a fishing rod, a bow string, a base for a snare and other purposes. The base is located under the outer covering and serves to enhance the load-carrying capacity;
• External covering. It is woven from many ultra-thin threads into a single tube-shaped fabric. It bears the main load. After pulling out the core, such a rope will be able to lift significantly less weight. However, the load capacity will never drop by more than half, because a rope of medium thickness without a core can support two people of normosthenic build.

Figure 2. 550 paracord (left), 750 paracord (middle) and inner rope view (right)

The maximum load capacity of the cable varies depending on the total thickness.

The average cable can withstand more than 250 kilograms and weigh up to 100 grams.

This criterion is used to select the best material.

The following options are available on the market:

1. Paracord 100: 1.6 millimeters, 45 kilograms, 1 rope in the core;
2. Paracord 425: 3 millimeters, 181 kilograms, 4–7 ropes in the core;
3. Paracord 550: 4 millimeters, 249 kilograms, 7–9 ropes in the core;
4. Paracord 750: 4 millimeters, 340 kilograms, 11 ropes in the core.

When calculating thickness, it is necessary to remember the errors that are allowed by each manufacturer. With the same diameter, the load capacity may drop to 10–20 kilograms, and the number of middle cords will differ from the parameters stated above. It is for this reason that it is recommended to order cords from trusted suppliers (Figure 3). American and German suppliers are considered the leaders. They clearly indicate all the features of the lace, unlike their Chinese counterparts. Chinese ones often withstand 2 times less weight than originally stated. If your life depends on the quality of the cable, treat your purchase with the utmost responsibility.

The following tips will help you determine that what you are looking at is not a fake:

Paracord Weaving Tools

Once the material is selected, it is not enough to download the diagram and start weaving the accessory. The guarantee of quality will be tools for weaving paracord. They will help create symmetrical and even loops, and will also significantly speed up the overall process. Thanks to this, in the period of time it took to create one product completely by hand, you can make two or even three. Since survivalist bracelets require high quality and maximum efficiency at all stages of creation, it is recommended to purchase accessories.

Accessories for weaving paracord (Figure 4):

Patterns for weaving a paracord bracelet

Paracord weaving patterns vary in style, level of complexity and amount of lace used. Most users do not succeed in quickly unraveling bracelets the first time, so it is recommended to practice on shoe laces or ropes so as not to damage the cord. After the training product unravels in an instant, you can move on to the main material.

The most popular methods of weaving paracord include the classic one. You can begin the process without prior preparation. Unlike other schemes, in this case weaving knots with paracord does not involve. To create, you will need a two-meter cable of medium diameter, a fastener (plastic or a specialized carbine with flint), cauterization matches and scissors or a sharp blade for needlework.

Classic weaving pattern:

1. The rope should be folded in half and inserted into the recess of the carabiner. The free edges are drawn into the resulting loop and a knot is tied;
2. The second half of the fastener is attached to the ends. The accessory is tried on directly on the wrist to determine the approximate length. If the loose slings are too long, it is not necessary to cut them, since the loops can be made wider;
3. To tie the loops, alternately loop each end through the two secured middle slings. The edge is wound from the bottom up in one direction and from the top down in the other. The classic style is similar to the braid hairstyle;
4. To secure, the ends are passed through the fastener again, cut with sharp scissors and a blade, and lightly melted with fire.

Cobra. Weaving a cobra from paracord requires some preparation and is more complex in terms of execution.

Figure 5. Weaving pattern for the “Cobra” bracelet

Cobra weaving pattern (Figure 5):

1. Fold a three-meter paracord rope in half, thread it through the fastener and secure it, as in the instructions for the classic scheme;
2. Place the second part of the fastener on the free ends and measure the distance using the following formula: “comfortable length for wearing + two fingers.” An indent of two fingers is necessary for double-sided knitting;
3. Throw the loose ends through the clasp. Further knitting of loops will take place around the fixed middle lines;
4. Take the left line and place it at a 90 degree angle on the middle lines. A loop will appear on the left, and both ends will point to the right;
5. Take the right tip and bend it around the left cord, inserting it from top to bottom into the loop on the left. After the slings point in different directions, they should be pulled until the knot is tightened;
6. After this, the process is repeated in the opposite direction. The directions change alternately;
7. Be careful that the loops are not too loose or too tight. Once one side is completed, flip the accessory over and start weaving from the inside. There can be many layers, and they are created until the material runs out. Then the extra centimeters are cut off and cauterized.

King Cobra. A wide weave of paracord up to the middle is performed using the Cobra algorithm, then supplemented with a cable of a different color.

Figure 6. "King Cobra"

King Cobra weaving pattern (Figure 6):

1. The cord is folded in half and placed under the unfolded bracelet with a loop on the right and free ends on the left. The lower tip is released and thrown over the accessory perpendicularly;
2. The upper left tip is passed along the front side of the product, its edge is pushed from top to bottom into the right loop. Ultimately, the ends point in different directions and need to be pulled, thereby tightening the knot;
3. The action is performed in the reverse order, then vice versa and is carried out until the new cord completely covers the surface of the finished accessory;
4. The ends are cauterized and inserted into the clasp.

The technique of weaving paracord King Cobra is very popular among travelers, because after unraveling the bracelet, you get not one, but two ropes.

Weaving a whip from paracord

Weaving a whip from paracord will be an excellent replacement for leather analogues and is carried out according to a standard algorithm for arapnik manufacturers.

Figure 7. Whip with paracord core

There are two types of creating arapnik:

1. With core (Figure 7). To make the core, several paracord cables are taken and wrapped with thick black electrical tape. Then new cords are fixed on top of the core and wound with electrical tape, from the free ends of which the weave will be carried out;
2. Regular without core. The accessory turns out to be much lighter and softer than the previous version, but the impact force is weaker.

In both cases, paracord weaving in a snake pattern is most often used.

Other methods of weaving paracord

In addition to those listed, there are other techniques. The list of paracord weaving includes knots that can be used to create an apple (the round end on the handle of an arapnik), key rings or a backpack.

Other methods include round paracord weaving. It is used both for making whips and for decorating knives and other bladed weapons using a lanyard.

Figure 8. Lanyard weaving pattern

A paracord lanyard is woven using the following pattern (Figure 8):

1. We take 1 meter of material, bend it in half and visually fix the length of the free loop by which the product will be hung or attached;
2. Each of the slings is wrapped in a loop, and their ends are pushed into the opposite loop. Then they tighten slightly. Thus, the first knot is tied;
3. We stretch the right loop and insert the left cord into it, tighten it again;
4. We turn the product over and repeat the operation without changing the right side. You can also start on the left side and maintain it throughout the workflow;
5. The remaining tips are cauterized or decorated with beads.

In this article, we looked at how to make a paracord bracelet, the most popular weaving patterns and methods of using this material.

Paracord is a parachute cord, and in English its original name looks like parachute cord. This is a simple nylon cable containing so-called cores.

The purpose of paracord

Even during the Second World War, these devices were used by American military paratroopers. Even today, paracord continues to be used in the military industry and is in high demand among hunters. It is even called a survival rope. Paracord (you already know what it is) is used as a strong and reliable cable.

And if we explore the possibilities of its use, it turns out that they are much wider than we can imagine. For example, the capabilities of paracord allowed astronauts to even use it to repair a telescope during the second Shuttle flight.

Paracord consists of many fibers intertwined with each other. It is thanks to this that manufacturers were able to obtain a smooth surface. As for elasticity, nylon contributed to it.

Use of paracord today

What it is - paracord - should be examined in detail. As we have already said, the use of this material is even wider than before. Paracord comes to the rescue in many situations where a strong cable with a high level of elasticity is really needed. This often extends to equipment that uses shoulder-belt systems. Among other things, paracord weaving is used in the following cases:

• Quite often it is used for lanyards. This is the name given to the cords or brushes on the handle of any tool or edged weapon, which help secure it to the hand, preventing loss or slipping.
• Paracord is used to attach backpacks to shelves.
• Attach camouflage nets to trees.
• In some cases, high-quality fastening of equipment is carried out.

DIY paracord

Paracord is great for weaving. Wicker items made from paracord of several colors seem especially expressive. These can be bracelets, straps, cases for flash drives, key rings for keys and phones, as well as braiding for the handles of knives, lighters, flashlights, etc. Having learned for sure that this is paracord, we can say with certainty that weaving from it is based on the use of various types of structures. In this case, a decoration or a belt made of paracord, in addition to a decorative function, will also serve a practical function, since in a matter of minutes you can have a strong cable in your hands.

By the way, to produce a bracelet you will need approximately 4 m, and for a belt it will take at least 15 m.

It is enough to master the general principles of paracord weaving, and you can always make a wonderful gift with your own hands that can please friends and family.

How to distinguish fake from real paracord

How to weave paracord - The question is quite broad and complex. The technique of this action is not simple and requires special attention and accuracy. But it is worth remembering that only high-quality paracord can help you out in difficult times and also become an excellent decoration. Therefore, you should be careful when purchasing it:

1. When choosing paracord, you can tell that it is real even by touch. A soft surface will give good quality.
2. If you set fire to the edge of the cable, it will smoke and smell like melting plastic.
3. In addition, the edges and core will melt unevenly - the outer shell will burn faster and expose the core.
4. High-quality paracord can withstand a weight of up to 250 kg, while a fake one will break at a weight of 50 to 100 kg.

It is worth noting that such material cannot be used as a cable for mountaineering.

Stages of weaving paracord

It is quite difficult to weave paracord with your own hands, and making a bracelet from it is even more difficult. But if you try and be careful, then everything can work out at the highest level. Next, we will look at patterns for weaving paracord in the form of bracelets.

It's nice to wear them on your hand when going not only to a friendly party, but also on a hike. And if you need a rope, you can quickly dismantle it.

You will need a fastener, a lighter and tweezers. About 2 m of paracord is needed:

1. We burn one end of the rope and make 4 loops in the fastener slot.
2. Now we make a loop from the long part and pull it through 4 loops in the fastener by about 5 cm, after which we tighten the loops in turn from right to left.
3. We loosen them and, using tweezers, pull out 3 more loops between the pairs of loops, and leave the fourth on the side. We turn them so that their left side is in front.
4. We pass the running cord through them, as in point 2.
5. Tighten the loops from right to left.
6. You need to go through steps 2, 3 and 4 again.
7. When the length is suitable for you, you need to stretch the running cord to the last row and make 3 more loops for the second part of the fastener.

Light the rest of the cord with a lighter and thread it through any loop or tie it in a knot.

Weaving patterns

For such bracelets there are many weaving patterns - “cobra”, “double cobra”, “snake”, “stitch”. It must be emphasized that the sphere of paracord weaving was initially formed spontaneously due to the simplicity of these products, so in some cases the same weaving pattern may have several names.

Cobra weaving pattern

One of the simplest methods is, of course, “cobra”. As a rule, there can be 2 or 4 threads on the inside of such a bracelet, therefore, the decoration can be thinner or thicker. To do this you will need 2 cords of similar length.

For each centimeter of weaving produced, you need 6 cm of any rope and a few more, for the convenience of weaving the very last links. When using the cobra pattern, you can use two-color threads. The pattern called “double cobra weave” is distinguishable by a width that is 2 times larger due to the connection of 2 parts.

Synthetic paracord cord- a fairly durable and thick material that comes in a variety of colors. Its main purpose is functional application in a wide variety of areas. But, despite its utilitarian nature, it began to be used for weaving various types of jewelry. This is quite simple to do, as the macrame technique is used.

Paracord is a type of cord made of nylon fiber and having a thick diameter. It began to be used for military purposes, and also as parachute lines. Now the scope of application has expanded, and such an unusual strand is even used for weaving jewelry. This is due to the fact that the military style in jewelry made from cord is now very popular.

The strength of paracord is achieved by specially interweaving several thinner fibers. But in the case of weaving a bracelet, the question arises: how to choose the right material? Several answers can be given here.

If the bracelet is woven exclusively for decorative purposes, then you can buy its analogues in the department selling handicrafts. If you need to weave a bracelet for functional use, then it is better to go look for real paracord where they sell sports equipment or to hardware stores. True, in this case, the color range will be limited.

The history of the emergence of a paracord bracelet is interesting. The fact is that boy scouts, trying to save space in their backpacks, wove bracelets from such a cord. The bracelet contained 3 m of paracord. If necessary, the bracelet could be easily unraveled and the cord could be used for rational purposes. Then it could easily be woven back.

Later this idea was adopted by tourists, hunters and fishermen.

Weaving a paracord bracelet: features

Before weaving a bracelet on your hand yourself, You should familiarize yourself with the features:

• you need to buy about 2–3 m of cord;
• It is advisable to choose several colors, then you can get bright colored bracelets;
• for ease of operation, a cord is needed to which the braided threads will be attached;
• Special clamps can also help.

How to weave a paracord bracelet with your own hands - 3 master classes

It takes a little effort to get the bracelet. The technique used in the work is macrame.

Cobra

Most often, Boy Scouts wove a cord that formed a pattern, called cobra. It looks great in two-tone. Woven in 4 threads. The two inner ones are one color, and the left and right ones are another.

The sequence of actions when weaving a cobra bracelet:

1. First, a thread of the same color is attached to a cord that serves as a lock.
2. When fastening, you can leave a small loop, which will later serve as a clasp. To do this, it is enough to leave a loop no more than 2 cm long.
3. Then a thread of the second color is attached. It should be left intact, despite the fact that when fastening the cord should occupy the extreme left and right positions.
4. The left thread is laid out horizontally, on top of the other three. With its help, a loop is formed and the end is thrown back to the left. Then the right thread is taken and brought from above into the formed loop.
5. Then it should be passed from below under the two central cords. And the end is brought out from the bottom up between 2 and 1 thread on the left side.
6. The end of this cord is laid out over the left end from which the loop was formed. Then again the end is brought down under the two main threads. And it is brought out from the bottom up into the formed loop on the right side.
7. Then you need to slightly pull the outer ends so that a knot is tied on the two central cords. Repeat this combination of steps until you have a complete bracelet.

If the product is made long, you can weave a cobra pattern and a belt.

Simple weaving

The second bracelet is also quite simple. You can also take two colors for it. One of them is the base, while the second lace is braided around the first.

In order to make weaving, you need to fold one thread in half - it will be the base.

1. The second thread is folded into a loop and the ends are inserted from left to right.
2. Then the ends are crossed and the lower thread is brought through the warp into the loop.
3. It is necessary to tighten the ends to form a knot.
4. Then repeat the braiding of the threads, but on the other side.
5. Thus, knots are tied either to the left or to the right of the two threads forming the center.
6. Weaving continues until the desired length is achieved.

Weaving with a single color thread

This next bracelet is quite impressive on its own.

You can use a plain thread for it, but it will look best if the thread is a bright color.

1. A Celtic knot is made at one end of the thread.
2. Then two large loops are made from the Celtic knot, directed from the bottom up. The length of the loop should be equal to the circumference of the wrist and the loose fitting allowance. Pull the end through the loops.
3. Then it is passed to the center between the two threads. It is displayed from the bottom under the two leftmost threads up. And again it is passed to the center of the loop and brought out from the right side from the bottom up.
4. This movement is repeated several times until the entire length of the cord is braided.

What other bracelets can you weave?

You can weave absolutely any bracelets from a thick paracord cord using macrame knots.

It can be both single-color and two-color, three-color and multi-color products.

As for the weaving technique, it can consist of simple knots and include from two to four threads. Or it can be quite complicated. In this case, a large number of cords are taken. And often an additional hook is used.

Regardless of what product you choose for weaving - simple or complex, single-color or multi-color, the result will always be original.