Everyone Have a good mood! In this post, we will talk about how set up internet on computer via cable. Moreover, friends, that once upon a time, this topic was already discussed on this blog.
But with a lot of water under the bridge since then, and with new PCs ubiquitous with Windows 10, there's an urgent need to update the information. Although, to be honest, nothing much has changed in this matter.
So, since unlimited is going by leaps and bounds across the expanses of our vast homeland, within the framework of this publication, connection via a modem that is configured in router mode will be considered.
Therefore, if someone else does not know where to plug in the network cable correctly or why you need the login and password that you were given at the subscriber station, be sure to read the following material:
After the computer is connected to an already correctly configured modem using a cable, the matter remains small. You just need to configure the network card. This is done very simply, there will be no problems.
In the future, everything will be shown using Win 10 as an example, although in previous versions this operating system, everything is done by analogy. So let's get started. Right-click on the "Start" button, and then select the "Network Connections" section:
A window will open in which you need to select a wired connection, because we are connected via a cable. Usually it is called "Ethernet" or "Connection via local network»:
Now right-click on it again and go to Properties. At the next stage, you need to select the "IP version 4" item and click the "Properties" button below:
- IP Address: When using dynamic IP, this is any value between 192.168.1.2 and 192.168.1.254. If there is a permanent IP address, you should specify it;
- Subnet mask: determined automatically, do not touch anything;
- Default gateway: specify the IP address of the modem that distributes the Internet to the computer via the cable.
After that, go to the item "Use the following DNS server addresses". Here you need to specify the values \u200b\u200brecommended. In case you do not know them, you can use universal ones. Here they are:
At this point, it is important to understand the fact that it is thanks to these addresses that sites are opened in a computer browser. Therefore, with their help, you can block certain resources. Look at the third line of the table above.
In short, after all the manipulations, press the "OK" button and begin to enjoy the work of the Internet. If suddenly the sites still do not load, then it is strongly recommended to check the settings again, and then study this article:
And on this article on how to set up the Internet on a computer via a cable has come to an end. If you have any questions, be sure to ask them in the comments. And look at the end interesting video about Russian people on the web.
There are an inspiring set of modern technologies for accessing the World Wide Web - these are wireless networks, fiber optic cables, 3G and 4G modems. Each type of Internet access has positive and negative characteristics, such as cost, speed, and stability. And the question of the complexity of the connection has not changed. Is it necessary Additional services a specialist, or can everything be set up without assistants?
Preparing to set up an Internet connection
VPN connection, PPPOE, L2TP
PPPoE connection
If errors 651 occur when configured correctly, then the problem is related to blocking or deactivating the computer's MAC address. To resolve the issue, you will have to contact the support service, describe the error and name the physical address.
Installing a home router
Is your home computer directly connected to the Internet via a fiber optic cable? And a recently purchased laptop is completely cut off from outside world? The ideal option is to buy wifi router(router), independently configure the equipment and provide the entire apartment with wireless access to the network, including a laptop, phone and tablet. The Internet fee will not change, everything is according to the tariff!
- Search suitable place for the router. It is better to place an uninterrupted Wi-Fi source in the center of the working area to ensure a stable signal. It is important to set the optimal height and location - a competent choice will increase the overall coverage.
- Tooling. Wi-Fi router, first of all, should be provided with power from the outlet. Further connect to router a laptop with a wire with two plugs (into any slot marked with either numbers or LAN names) hidden in the box with the purchased equipment. And then plug the cable provided by the provider into the WAN connector.
- Driver update. Any software must be installed in advance from the attached disk.
- Setting. The method of resetting information in the TCP/IP v.4 protocol is described above, but in short, in the protocol properties, you must set the automatic method for obtaining information about IP and DNS servers.
Setting up Wi-Fi on a laptop
- If the IP is automatic, then you don’t have to configure anything, just select the connection type in the main settings and correctly connect the router to the equipment.
- Connecting PPPoE requires entering a login and password, and at the same time setting up a DNS zone. All information is issued by the provider at the conclusion of the contract, so you should carefully consider all issued papers.
- Static IP. Copied from LAN settings and written to WAN settings.
- L2TP. All information is issued and filled in the appropriate fields.
- The indicator in the panel will notify you about a correctly configured network wireless access. But go to exploitation wifi yet early, the connection must be branded with a password and restricted from unwanted guests. The WPA service will do the job just fine. So, go to the home page of the router, the "Security" tab. The security type is selected first, then the password. Save the entered settings, reboot the router, you're done!
Connect to an available Wi-Fi hotspot
Receive Free access To wireless internet can be found in almost any modern cafe, restaurant or mall. It is enough to activate the Wi-Fi module on your laptop, select a free connection and start surfing the pages of the World Wide Web. But how are things in practice?
Learn more about activating the Wi-Fi module on various laptops:
- HP. The F12 and Fn keys together enable the corresponding service. The Wi-Fi icon on your keyboard will change from a dull red to a glowing blue.
- ACER. The same (regardless of the series) combination of Fn and F3 activates the connection menu, allows you to select desired point access.
- ASUS. Activation by simultaneously holding Fn and F The icon lights up, information about the connection pops up.
- TOSHIBA. The buttons on the keyboard (Fn and F8) help, when the network is active, it opens access to the menu for selecting a future connection.
- SAMSUNG. A typical use case for a combination of Fn and F The control panel opens immediately.
If the function specified in the list does not work, then it is worth first of all to look at the keyboard. Find on the functional part a key depicting a network connection. Press in combination with Fn. Sometimes the activation method through special software installed with the drivers helps.
The second option for troubleshooting is uninstalled drivers for the network card, or for the module WiFi. Installation required software from the disk attached to the laptop, or using the modern DriverPack Solution utility, in automatic mode installing missing drivers. find necessary files you can also visit the manufacturer's website through a search, the main thing is to know the full name of the laptop.
The speed and stability of a wired connection often make it a better choice than wireless. Connecting a laptop to the Internet via a cable is sometimes more convenient than via Wi-Fi. For example, transferring a file over a home network from a computer to a laptop and back is much faster and more reliable than using a wireless connection.
There is nothing complicated in installing a cable connection. It is enough to insert the wire laid by the provider to the subscriber's side into the appropriate connector of a PC, laptop or router.
Setting cable internet may differ depending on the connection type and lesser degree from the operating system. For Microsoft products noticeable differences are only in Windows interface XP compared to more recent versions.
Next, consider the main important points to be taken into account when connecting wired internet. A sequence of steps for setting up the most common types of cable connections in a Windows environment.
Provider selection
Before you configure something, you need to have the Internet in the room. Communication service providers will help with this, from right choice which depends on the further comfort of staying in the network. When exploring options, it is important to consider the following factors:
- Possibility of laying a network cable to the subscriber's side;
- Cost of connection and services provided;
- Terms of tariff plans;
- Availability and responsiveness of the support service;
- Promotions, bonuses, discounts provided by the provider.
Tariffs, promotions, connection availability - most of the operator companies post all this information on their websites. About the quality of communication and support, it is better to ask your friends who use the services of the provider of interest.
Video tips for choosing an Internet provider:
Having decided on the choice, you must submit an appropriate application. This can be done by phone, on the company's website or in person by visiting the office.
Types of wired connection
Methods for cabled access to the network differ depending on the equipment, cable and software technologies used. To choose the most profitable and convenient option, you must first familiarize yourself with existing varieties wired internet.
- xDSL is a telephone line connection using a splitter to separate voice and internet data frequencies. Max Speed(ADSL) 24 megabits.
- FTTB - optics to the building. High-speed method used in multi-storey buildings. From the provider side apartment building an optical cable is laid, connected to the switch, from which the Ethernet patch cord is routed to the subscribers' apartments.
- xPON - a fiber optic cable is brought into the house, connected to a special router with an optical input, from which the Ethernet wiring comes. The most promising and high-speed option (up to 1 Gbps).
Setting up a laptop to connect to the Internet via cable
System configuration depends on the hardware and network protocols used by the particular operator. When configuring client equipment, DHCP and PPPoE are most common.
Dynamic or static IP (DHCP) - settings for Windows
First you need to directly connect the Internet to the client device through the provider's cable. If the connection is not working properly, the network connections icon will display a yellow exclamation mark. This means that the cable is connected, but there is no Internet connection.
Editing the network connection options will help correct the situation. To do this, right-click on the corresponding icon in the notification area. In the menu that appears, click on the item go to the network and sharing center.
On the page that opens, look at the navigation on the left, go to the section for changing adapter parameters. We highlight the LAN connection, which indicates the name of the network card, usually these are Realtek or Atheros models.
Right-click and select "Properties" from the drop-down menu.
Connection options will open, in which we double-click on the "IP version 4" parameter or select it with one click of the right mouse button and click "Properties".
Then you need to configure the Internet protocol TCP/IPv4. Depending on the networking technologies used by the provider, there are two options: dynamic or static IP.
Dynamic IP. If a DHCP server is running on the provider's side or it specifically indicated that you need to use dynamic IP in the connection parameters, then in the protocol options we activate the switch "Obtain an IP address automatically" and "Obtain DNS server address automatically". Confirm by clicking "OK".
Static IP. In this case, the operator must provide the following data: IP address, subnet mask, default gateway. In addition, DNS server addresses can be provided. To fill in the corresponding fields, you must enable the radio buttons "Use the following IP address" and "Use the following address of DNS servers".
If all required parameters were specified correctly, the connection will be established automatically after the cable is connected.
PPPoE
In this case, the provider provides not an IP address, but authorization data - a login / password pair. To connect a laptop to the Internet via a network cable using PPPoE technology, you need to add a new connection in the Network and Sharing Center.
If everything is done in accordance with the above instructions, and the correct user authentication data is entered, you can click "Connect" and enjoy the comfort and speed of cable Internet.
Video on connecting PPPoE on Windows 10:
Perhaps it is difficult to find a person who does not use the Internet. Access to the World Wide Web has filled our lives both at work and at home, from children to the elderly, because many of them also try to keep up with development. computer technology. Therefore, the problem of connecting to the Internet is relevant for a wide audience. After reading this article, you will understand that connecting a computer to the Internet is not difficult at all. Because many people prefer latest version software windows software 8, the article describes the actions of the user of this particular system, but if you have a different edition of windows, you can also use this instruction, basically the connection system is the same.
First, decide on the source of access to the Internet: a fixed connection, a Wi-Fi router or mobile Internet (via a SIM card). Contract with a provider if necessary, and they will usually provide you with necessary equipment, starting with a cable and ending with a high-speed modem or even a router. In case of use mobile internet you need to purchase a special modem or use mobile phone that is connected to the computer via a USB port. But in this case, the speed of the Internet is much less.
As soon as an Internet connection is provided, start setting up the computer itself. To do this, enter the Start menu through account administrator. In the window that opens, press the right mouse button and the heading "All applications" will appear in the lower right corner. Select it by pressing the left mouse button.
Among all applications, select "Control Panel". A new window will open different categories of options for setting up your computer, open the second one in the list - "Network and Internet".
Then go to "Network and Sharing Center", where in the upper left corner click on the option "Change adapter settings".
In the "Network Connections" window that opens, move the cursor to the "Local Area Connection" symbol and call the context menu with the right mouse button. Among the proposed functions, select "Properties".
Go to the "Network" tab, highlight the heading "Internet Protocol Version 4 (TCP/IPv4)" and click on the "Properties" button.
In the next window, configure the final settings: check the boxes next to the functions “Obtain an IP address automatically” and “Obtain DNS server address automatically”.
If desired or necessary, in case of network failure to set the addresses automatically, you need to adjust the parameters manually. Contact your network provider for the necessary information.
Connecting a computer to a wireless WiFi networks, repeat steps 2 and 3 first. Next, open the "Network and Sharing Center" and click on the "Connect to a network" option.
A window will pop up on the right, showing the network connection settings. See if airplane mode is active - it should be off.
Below is a list of available connections. Left-click on the network of your choice and you will see an offer to connect - click on it. You can also check the box next to the "Connect automatically" line - and your computer will connect to this network itself, if it is available. Usually, when checking network requirements, you need to enter a password, but sometimes there is also “free” Wi-Fi, which is provided by some establishments.
If you have followed all the instructions exactly, then your computer is already connected to the Internet, and you can enjoy access to the global information network. Otherwise, contact the customer service center of your provider, and specialists will definitely help you solve all the problems. If you have any questions, watch the video, which also illustrates step-by-step instruction internet connection on windows 8.
SovetClub.ru
How to connect your computer to the internet
Today, there are almost no people left in the world who would not use the possibilities of the Internet. Therefore, the relevance of the question of how to independently connect the Internet to a personal computer is growing every day. A PC that is not connected to the World Wide Web turns into an ordinary typewriter with calculator functions, that is, most of the advantages of owning such a computer are simply lost. Below is a guide on how to connect a computer to the Internet, as well as step-by-step instructions on how to set up the Internet without resorting to the services of specialists. 
Preparatory activities
To connect to the Internet, first of all, you should choose the optimal one for specific conditions user's Internet source: direct connection (connect the Internet to the computer via cable), Wi-Fi router, SIM card mobile operator, satellite communication, automatic telephone exchange. Then, if necessary, sign an agreement with a communication service provider, which is called the "Provider".
He will provide his subscriber with the necessary means, for example, a modem or router, cable. If it will mobile operator connection, then a special USB modem, which is inserted into USB port computer.
Direct wire connection
The method has a number of significant advantages, but is not without major drawbacks, which can be decisive when choosing a connection method by the user. It is very easy to implement and requires the least cost. However, the Internet provider must extend the wire directly to the computer, which is not always possible and convenient. The cable must be connected to the network card of the PC.
After that, you need to configure the Internet in the computer. The input parameters differ depending on the communication service provider and the connection technology itself. The essence of the procedure is to create a connection with authorization. The following is an example step by step actions on a PC with an operating windows system 8. In other operating systems supported by Microsoft, the procedure is similar.
It is necessary to perform the following sequential steps:
For windows XP, you can briefly imagine a similar algorithm of actions in the form of the following chain:
- Start;
- Network connections;
- Create a new connection;
- New Connection Wizard;
- Connect to the Internet;
- Establish a connection manually;
- High speed connection;
- Entering parameters from the Internet provider.
For windows 7:
- Start;
- Control Panel;
- Network and Internet;
- Network and Sharing Center;
- Setting up a new connection or network;
- Internet connection;
- high speed;
- Entering parameters from the service provider.
Using a router connected by a cable connection to the Internet
This is a more convenient option for home or office, as it allows you to connect more than one PC to the global network, but several at the same time, thereby creating a local network. Today, it is rare for anyone to have only one computer in an apartment or office.
Insert the cable from the provider into the WAN port of the router. Connect computers via LAN connectors using patch cords. Enter the provider's settings through a web interface launched in a computer browser by entering the address written in the router's instruction manual (usually 192.168.1.1).
Via WiFi router
When using a wireless router, the steps will be similar to the previous instructions, but you will also need to configure WiFi. If the computer does not have a Wi-Fi adapter, then you will need to purchase and install it.
Using Windows 8 as an example, to connect a computer via Wi-Fi, you need to do the following:
Using the network of a mobile operator
Despite the relatively slow data transfer, this option is very popular among users due to its high mobility. It is enough just to insert a USB modem into the corresponding port of the computer, and the setup will be performed almost automatically, the client will only need to follow the instructions of the setup wizard. 
www.nastrojkin.ru
How to connect the Internet from a router to a computer (laptop) via a network cable?
Many articles have already been written on the topic of connecting to the Internet via a wireless network. Instructions for connection, solution different problems, errors, etc. And in this article we will consider connecting the router to a computer using a network cable, which usually comes with the router. With a cable connection, everything is much easier than with Wi-Fi. But despite this, sometimes there are issues with connecting to the router using a network cable (LAN).
Basically, of course, stationary computers that do not have a built-in Wi-Fi receiver are connected to the Internet using a cable. And if you buy a special Wi-Fi adapter for your computer, then here you can also refuse wires. I always advise you to connect the router via cable to configure it, and of course firmware updates. There are different cases, maybe Wi-Fi does not work on a laptop, but you need to connect to the Internet, or the speed over a wireless network is low, here we need a network cable. A cable connection is always more stable than an air connection.
All we need is the network cable itself, with which we will connect the computer to the router. This is a regular twisted pair cable with RJ-45 connectors on both sides. This cable should be included with your router. True, it is short there (depending on the manufacturer of the router). If you need a long cable, then you can make it in a computer store. You can do it yourself, but you need a special tool. There are plenty of instructions on the internet.
As a rule, 4 devices can be connected to the router via a network cable. It is 4 LAN connectors that you will most likely find on your router. V individual cases, LAN connector can be 1, or 8. No matter which windows version installed on your computer. The instruction is suitable for windows 7, windows 8, and windows 10. In windows XP, everything is connected in the same way, but the IP settings will be slightly different.
Connecting to a router using a network cable (LAN)
Everything is very simple. We take a network cable, connect one end to the router to one of the LAN connectors (they are signed LAN, or Home Network). And the other end of the cable is connected to the network card of the computer. It looks like this:
If you connect a laptop to the router, then we do everything in the same way. One end of the cable to the router, and the other to the network card of the laptop:
That's all the connection. If the router is turned on, then the computer should immediately respond to the connection to the router. The connection status in the tray will change (in the lower right corner).
If the Internet is connected to the router, and it is already configured, then most likely the connection icon will be like this:
This means that everything is fine, and the Internet is already working.
And if the router is not configured yet (you are just going to configure it), or there are some problems in the computer settings, then the connection status will be yellow exclamation point. And no internet access. The Internet will not work on the computer.
If the Internet from this router works fine on other devices, but on the computer that we connected without access to the Internet, then you need to check the IP and DNS settings for connecting via local network.
No internet access when connected via cable
It may be that after connecting the Internet will not work. The connection will be "no internet access", or "Limited" (in windows 8 and windows 10). If the problem is not in the router (it distributes the Internet), then you need to check the settings on the computer itself.
Right-click on the connection icon and select Network and Sharing Center. In the new window, select Change adapter settings.
The Internet is full of news about how to solve the problems of connecting to the global network using wireless technologies. However, when connecting a wired Internet, a lot of problems can arise that will not allow you to receive information from the global network, although they are much less common. If the Internet does not work via cable, the user must clearly know the reasons, as well as ways to solve this problem.
This article addresses the issue of Internet access problems by directly connecting a LAN cable to a computer or laptop, from a router (direct cable connection from a provider is practically no different, only in this case there are slightly fewer reasons for inoperability).
As a rule, the network cable is connected directly to the computer due to the fact that it is not provided and such components are not connected. Of course, you can purchase a special Wi-Fi receiver that can be connected to the Internet to get rid of unnecessary wires located around the apartment, house or office. But this step is not always appropriate, because the computer is by no means a portable device that can be moved at any moment. That is why, in order not to spend extra financial resources, most computer users use a direct LAN connection.
First of all, if you cannot connect to the Internet, you need to check the following factors:
- is the cable that connects the router to the computer working (try to use it when connecting to another device);
- check the operability of the Internet channel (connect directly the LAN from the provider to the network adapter);
- whether the connection to the router is active (whether the LAN light on the router is on);
- pay attention to the network icon, which is located in the tray (the computer reacts at least somehow when connecting and disconnecting the network cable, and also whether the network is identified);
The above factors are the main reasons for the lack of Internet connection. If the LAN cable connecting the router and the computer is not working, it is enough to replace it. If no devices, with a direct cable connection from the provider, also get access to the Internet, this issue must be checked directly with the provider, who are required to check the integrity of the cable along the entire route, from the computer. Of course, if the LAN cable connection light on the router is not on, you need to check the connection and performance of the router itself.
The most non-obvious problem is the inability to connect to the Internet if the network identifier in the computer tray is lit with a red X or a permanent network identification is performed that does not allow you to connect to the Internet. Let's consider this question in more detail.
The computer does not respond to the LAN cable connection
If the red X is constantly on the network icon, the reason is that the network card is working.
To check the network card, do the following steps:
- open "Device Manager"
- right click on "My Computer"
- "Control"
- go to Device Manager).
You will see a list of all devices that are installed on the computer. Open the list " Network adapters”, where you will have all the network cards that are installed on this computer (in most cases, it is the only one that is integrated into motherboard, but may be more).
If a yellow icon with an exclamation mark is lit opposite it, you need to reinstall the drivers for this device. Visit the official website of the manufacturer and download the drivers for your specific network card model and install them (it is better not to use the automatic driver search, but to do the installation manually).
If the Internet is still unavailable, do the following:
- go to "Control Panel"
- go to the "Network and Internet" window.
- you may have a tritely disabled installed network device. To enable it, right-click on the icon and select "Enable".
The circle is constantly spinning Identification or the network is not recognized
This reason may occur when there is a conflict between IP addresses that are present on the network.
To resolve this issue, you need to:
- go to the "Network and Sharing Center";
- click "Change adapter settings";
- on the icon of your network card, right-click and select "Properties";
- place the cursor on "IPv4 Internet Protocol";
- set a bullet to automatically obtain an IP address and DNS server.
If you have a yellow triangle on the network status, in this case, you have incorrect router settings that do not allow you to connect to the global network.
In such a situation, it is necessary to install correct settings router (instructions should be posted with your ISP on home page, or they can give them to you in the form of a printout) or take the router to the provider so that they configure the device correctly. Also, a similar sign may appear if you have not paid for the Internet and you have been tritely disconnected from the network.
